in

How To Fix iPhone 6 Plus LCD Display



Whole machine disassembly course
(1) Cell phone off
1. First, turn off the iPhone 6 plus. Note: if the screen function is not normal, you can press and hold the power key and return key at the same time until the shutdown dialog box appears on the screen, and then let go.

Apple iPhone 6 plus
(2) Remove the bottom screw
1. Remove two pentagonal screws beside the charging socket. Do not use the wrong screw driver. The wrong screw driver will cause the screw to slide
Note: the screws to be removed should be placed separately (the screws distributed vary in size according to requirements). Therefore, it is not allowed to install the screws at will, otherwise some accessories will be damaged.)
Apple iPhone 6 plus
(3) Remove the face cover
1. Use the suction cup to pull the cover off the iPhone 6 plus
Apple iPhone 6 plus
(4) Remove the screws of the battery fixing plate and remove the battery connector
1. Remove two crosshead screws on the battery holder, and then take out the battery holder and put it aside. (Note: you must hold the screen up with one hand and remove the screws with the other hand to remove the battery holder.) When you open the screen, don’t be reckless and break the cable.
2. Use the flat end of the mobile phone crowbar to slowly lift the battery connector and remove it. (Note: pry up the battery connector carefully)
Note: the screws to be removed should be placed separately (the screws distributed vary in size according to requirements). Therefore, it is not allowed to install the screws at will, otherwise some accessories will be damaged.)
Apple iPhone 6 plus
(5) Remove the screws of the fixing plate of the display module and the connector of the display module
1. Remove the cross screw of the fixing plate on the motherboard, and then remove the fixing plate. (Note: turn the screw anticlockwise to remove it, but note that the lower screw is smaller than the upper one, and the force is moderate.) Note: the screws to be removed should be placed separately (the screws distributed vary in size according to requirements). Therefore, it is not allowed to install the screws at will, otherwise some accessories will be damaged.)
2. Use the tip of the crowbar to remove the cable. Just use a little force
Apple iPhone 6 plus

(6) Take out the fixing screw of fingerprint module and take out the fingerprint module
1. Using a cross screwdriver, remove the two cross screws fixed on the fingerprint module fixed piece, take out the fixed piece and put it aside. Note: the screws to be removed should be placed separately (the screws distributed vary in size according to requirements). Therefore, it is not allowed to install the screws at will, otherwise some accessories will be damaged.)
2. Use the flat mouth of the mobile phone crowbar to peel off the fingerprint module cable carefully. Do not use too much force, otherwise the cable will be damaged. (Note: 1. If the fingerprint module cable is damaged, the fingerprint function of the mobile phone will be invalid. 2. Fingerprint and fingerprint line can’t be used separately.)
Apple iPhone 6 plus

(7) Remove the screw of the earpiece bracket, remove the front camera and the earpiece
1. Remove the cross fixing screw on the earpiece fixing bracket and set aside for later installation. Note: the screws to be removed should be placed separately (the screws distributed vary in size according to requirements). Therefore, it is not allowed to install the screws at will, otherwise some accessories will be damaged.)
2. Remove the front camera, gently remove the receiver with tweezers, and put it aside for later installation.
Apple iPhone 6 plus
(8) Remove the front camera cable
1. Use a crowbar to gently loosen the front camera cable, and then put the cable aside for later installation.
Apple iPhone 6 plus
nine
(9) Take out the fixing screw of the liquid crystal assembly and the iron sheet of the liquid crystal assembly
1. Remove the cross fixing screw at the edge of the iron sheet of the LCD assembly. In the circle. Note: the screws to be removed should be placed separately (the screws distributed vary in size according to requirements). Therefore, it is not allowed to install the screws at will, otherwise some accessories will be damaged.)
2. Use a crowbar to pry the bottom cable. There is a small piece of iron at the bottom of the cable. If it sticks too tightly, you can heat it with an electric hair dryer first. The sticky glue will soften, which makes it easier to pry. Then remove the LCD assembly iron sheet
3. Disassembly completed

Share this: